Builder Beam Job Description Sample
Machine Operator/ Electron Beam Welder
Perform required duties to set up, operate and maintain one or two sequential lines of equipment to deburr and ultrasonically clean a variety of sized of low carbon backing material and high speed steel wire to electron beam weld the two materials to form bi-metal coil stock.
Mount pancake or oscillating coils of backing material on appropriate play out stand using overhead electric hoist. Spark test to confirm type of material and feed ebd through deburring rolls, washer, welder, defect detector and on to take up reel. Mount high speed wire at washer and feed through welder.
Set up welder, install inner and outer locks, and replace seals at vacuum chamber. Adjust welding beam, regulate speed, and adjust voltage and amperage as required. Inspect welded material with microscope to assure proper location, shape and quality of bead.
Remove and dispose of burring shavings. Remove burring rolls, clean mounts and bearings, add lubrication, reverse or replace rollers in matching pairs. Lap rollers in automatic lapping machine, wash and inspect sharpened cutters under microscope.
Maintain ultrasonic cleaner adding caustic solution; maintain level of warm and cold water rinse. Dump and clean tanks, change seals, felt pads, fluid, air filters, etc. as required.
Monitor operation throughout. Observe welding through optical lens make necessary corrections and adjustments. Note signal light as take up coil approaches capacity, run to visual mark, cut band and start end on new reel. Wire completed coil in two places and transfer coil to annealing or temporary holding rack using tilting table and overhead hoist.
Observe and obey all safety rules, regulations and practices and employ all safety equipment and devices.
Perform other similar or related duties as assigned or directed.
Knowledge of charts, specifications, and micrometers
1-2 years experience preferred
Use of numbers including decimals
Light physical effort required, equivalent to lifting, pushing, pulling 5 to 25 pounds
High School Diploma or GED Equivalent
Hours: X/O (3) 5a-5p (3) 5p-5a
Post-Doctoral Position In Ion Beam Science
The Laboratory for Surface Modification (LSM) at Rutgers University invites applications for postdoctoral scholar positions in surface/thin film analysis and surface modification. The emphasis is on the use of ion beams for ion beam microscopy, ion beam analysis and ion induced surface modification. LSM is a well-equipped and established laboratory with a full complement of facilities for ion beam-materials science on the nanoscale and other surface analytical probes. http://lsm.rutgers.edu/.
The successful applicant is expected to participate and initiate programs employing these probes in new and exciting directions. Current research groups are led by Profs. Leonard Feldman, Torgny Gustafsson, Robert Bartynski and Eric Garfunkel in a highly collaborative mode.
Air Beam Fab And Integration Assembly (Hdt (Huntsville, Al))
Responsible for assisting in the performance of a variety of tasks related to fabrication, construction, modification, and testing structures. Ensures high quality.
ESSENTIAL DUTIES AND RESPONSIBILITIES:
Assists with the integration, re-work, and repair of fabric structures (i.e. bonding, cutting, etc.); fabrication, assembling, construction, and packaging.
Assists with records data and photographic documentation.
May assist in troubleshooting prototypes with assistance from supervisor, manager, and/or Engineering Dept.
Responsible for maintaining a clean, organized, and safe work area.
Reports all accidents, violations, or infractions to the Production Supervisor and/or Production Manager.
May assist with the receipt and distribution of materials.
May assist with procurement of materials.
Attends training courses deemed beneficial to the position including in-house and external training.
Supports and participates in the Quality Management Program.
Performs other activities, responsibilities, and related duties as required.
Adheres to all quality and safety standards
Supports other projects and performs duties as assigned
High Energy Laser Beam Control Engineer/Technologist
Job Description: :
Analyzes, designs, and develops acquisition, tracking, and pointing (ATP) and adaptive optics (AO) - wavefront control (WFC) subsystems for high energy laser (HEL) systems. Evaluates, investigates, and performs applied research and development on emerging ATP, AO, and WFC electro-optical technologies to improve performance and reduce cost for HEL products and solutions. As part of an interdisciplinary engineering and technology team, collaborates with subject matter experts in software, mechanical, power, thermal, electrical, production, and specialty engineering to support programs, pursuits, and internal R&D activities.
Electro-Optics, Photonics, Directed Energy, Solid Sate Lasers, Beam Control, Fourier Optics, High Energy Laser, HEL, MATLAB, ZEMAX, Research & Development Environment, Modeling, Simulation and SIMULINK.
Technical proficiency in the field of HEL beam control, with specialized skill in at least one of these areas: ATP algorithms, atmospheric compensation, or beam stabilization and jitter control.
Proficiency in Fourier optics or multivariable controls modeling & simulation. Self-starter with initiative and tenacity to meet deadlines with quality products. Team-player with the ability to work with a diverse range of individuals and enable senior leaders to build and develop cohesive and effective engineering teams.
Effective in oral presentation. Good written and briefing slide development skills. Operative skill in MATLAB and industry standard software tools required to be effective in the position.
Demonstrated potential to advance in technical and programmatic responsibilities, supported by publications, advanced degree(s), and challenging program achievements. Demonstrated skill in both Fourier optics and multivariable controls.
Scientific and mathematical grasp of the theory and practice of atmospheric propagation of laser beams. Proficient in ZEMAX and SIMULINK. Experience in test-bed and instrumentation setup for experiments and demonstrations.
As a leading technology innovation company, Lockheed Martin's vast team works with partners around the world to bring proven performance to our customers' toughest challenges. Lockheed Martin has employees based in many states throughout the U.S., and Internationally, with business locations in many nations and territories.
Join us at Lockheed Martin, where we're engineering a better tomorrow.
Lockheed Martin is an Equal Opportunity/Affirmative Action Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, pregnancy, sexual orientation, gender identity, national origin, age, protected veteran status, or disability status.
Job Location(s): Sunnyvale California
Security Clearance :
Business Unit :
ESS4400 SPACE SYSTEMS COMPANY
Job Class :
Job Category :
Relocation Available :
Work Schedule :
9x80A-9,9,9,9,8 hrs/d in wk1, /9,9,9,9,off in wk2
Req Type :
Additional Posting Locations :
Electron Beam Furnace Manager
TIMET in Vallejo, CA is looking for Electron Beam Furnace Manager!
This job entails the following:
Manage and direct E.B. Furnace operations to achieve optimum utilization of manpower and equipment.
Maintain satisfactory quality standards and financial commitments. Reach safety goals and support development of new products/processes.
Interview, hire, train, supervise, evaluate, coach, promote and terminate personnel. Some of these activities will be conducted jointly with the production manager, and interviews, hiring, promotions and terminations will be coordinated through Human Resources
Review work order instructions, quality planning items, blend sheets, prior chemistry reports and other data as necessary to insure accurate direction of work crews
Collect in-process data and product data and analyze to verify conformance to procedures and specifications
Lead or participate in continuous improvement to processes, equipment and maintenance (maxim including recording of data and data analysis for measurement of melt center performance.
Develop and work to budgets to achieve cost management goals, and initiate or participate in cost reduction and/or profit improvement programs
Develop and work to attain productivity and yield goals
Manage engineering projects relating to furnace capacity expansions, new technology and/or equipment-based process improvements
Maintain an effective preventive maintenance program. Assist in problem solving for unplanned downtime.
Maintain adequate spares and supplies to meet schedules. Develop and maintain outside resources as needed.
Issue monthly reports documenting operational performance, achievements, projects, training and maintenance work
Accept weekend and holiday assignments as required
Act as coordinator of the plant safety program
Be willing and able to travel (typically less than 10%)
Effectively communicate TIMET and department goals, achievements, problems, solutions, practices, changes, and policies. Encourage positive communication. Enforce all TIMET policies, rules and regulations.
Conduct all operations in a safe and clean environment. Enforce all safety rules and regulations.
Maintain high ethical standards and integrity.
Maintain a program of professional growth through selected seminars, courses, trade magazines, books, journals, etc.
SUPERVISORY RESPONSIBILITIES Is responsible for the overall direction, coordination, and evaluation of this unit. Also directly supervises electron beam furnace operators.
Carries out supervisory responsibilities in accordance with the organization's policies and applicable laws. Responsibilities include interviewing, hiring, and training employees; planning, assigning, and directing work; appraising performance; rewarding and disciplining employees; addressing complaints and resolving problems.
Education and Experience
Bachelors's degree required (Electrical, Mechanical or Metallurgical preferred)
Minimum of 3 years of industrial experience (preferably in the metals industry)
Supervisory experience highly desired
Ability and desire to manage a 24 hour per day, 7 day per week small manufacturing operation
TIMET is an EOE
Beam Truck Driver
Job Summary: Good pay! Good benefits! Good people! At Knife River, we take care of our team because we know it's our people who make us successful. We are one of the 10 largest construction materials producers/contractors in the country, and we're growing! We are adding people to our team every day — people who are committed to working safely and to delivering high-quality results for our customers.
Knife River has an immediate opening for a Beam Truck Driver in Harrisburg, Oregon for our Prestress division! Our drivers are home every night and we offer competitive wages with a full benefits package. We seek to hire the best drivers in the area, and have a strong focus on customer service.
Responsibilities include, but are not limited to the following:
Safely haul over length prestressed concrete beams with a tractor trailer and remote steerable equipment.
Load concrete beams onto trailers and tie down loads for transport.
Rig different hauling combinations together.
Maintain driver's daily log and legal load limits.
Climb in and out of truck cab as needed throughout the day.
Maintain a clean truck appearance by complying with Knife River's operational policies, procedures and standards.
Assure all safety policies and procedures are followed to prevent any and all unsafe actions, processes and behaviors observed.
- Other duties assigned as needed.
- Previous truck driving experience.
Possess and maintain a valid Class A commercial driver's license with doubles and triples endorsements, medical card and a clean driving record.
Ability to pass a pre-employment criminal background check, physical/functional exam and drug screen.
Ability to work flexible shifts which include: days, nights, weekends and overtime. How To Apply To be considered for this position, candidates must complete and submit an employment application at jobs.mdu.com by the posting deadline noted above. If unable to complete an application online you may print and send completed application to any Knife River NW address or stop in one of our locations to complete an application. Knife River is an Equal Opportunity/Affirmative Action employer. All qualified applicants will receive consideration for employment without regard to race, age, color, religion, gender, gender identity, sexual orientation, national origin, disability, protected Veteran status or any other protected category under applicable state/federal law.
Subject to pre-employment drug testing and background check. Wage Details Wage range is $17.00 - $25.51 (when hauling) depending on skills and experience. Veterans: Put Your Skills to Work with Us! At Knife River, we are committed to helping our military transition to civilian life. We are constantly looking to add veterans to our workforce and want to make the transition as smooth as possible. There are many jobs within the military that are transferable to our Beam Truck Driver position:
Ground Transportation Apprentice
Ground Transportation Journeyman
Ground Transportation Helper
Vehicle Operations Apprentice
Motor Transport Operator
Motor Vehicle Operator
Logistics Vehicle System Operator
Assistant Beam Diagnostic Scientist
Provides the necessary design, analysis and testing of particle beam and photon beam diagnostics systems for the Advanced Photon Source accelerator systems. Provides physics support for the beam diagnostic systems for the accelerator. This work is carried out in collaboration with physicists and engineers associated with the accelerator sub-systems, under the direction of a senior staff member. Principal assignment is to support the group`s photon diagnostics for the APS storage ring and injector complex.
Good to considerable knowledge of the design, construction and operation of synchrotron light diagnostics including, IR/visible/UV diagnostics, X-ray beam diagnostics, laser technology and general accelerator beam diagnostic technology.
Ability to utilize state of the art analytic and simulation techniques in the design of accelerator diagnostics, the creation of drawings, and in the design of new beam diagnostic hardware.
Familiarity with electrical system troubleshooting techniques.
The ability to determine problem areas and recognize the need for additional expertise.
The ability to program in a high level language.
Bachelor's and 5+ years; Master's and 3+ years; Doctorate and 0 years, or equivalent.
As an equal employment opportunity and affirmative action employer, Argonne National Laboratory is committed to a diverse and inclusive workplace that fosters collaborative scientific discovery and innovation. In support of this commitment, Argonne encourages minorities, women, veterans and individuals with disabilities to apply for employment. Argonne considers all qualified applicants for employment without regard to age, ancestry, citizenship status, color, disability, gender, gender identity, genetic information, marital status, national origin, pregnancy, race, religion, sexual orientation, veteran status or any other characteristic protected by law.
PT System Engineer - Beam Physics
Job Description: Description de l'emploi Stellenbeschreibung 工作描述 IBA Proton Therapy is the industry leader in particle therapy, with the most precise clinical radiotherapy methods. IBA is internationally headquartered in Louvain la Neuve, Belgium with regional headquarters in Reston, VA right outside of our nation's capital Washington, D.C. With more than 30 years of success in cancer diagnostics and treatment, IBA is the worldwide leader of technology in the field of proton therapy. IBA currently has systems and treatment centers in Europe, Asia, North America and expanding to emerging markets throughout the world. The IBA name and mission has grown through the years making us one of the stand out companies to join; and who would want to work for a company that stands for the protection, enhancement and saving the lives of those fighting this horrible disease.
During the Installation/Commissioning phase of the equipment:
Participate to the installation of the equipment
Perform all different aspects of beam-related commissioning activities, involving much time on night shift.
During the Operations/Maintenance phase:
Operate PTS for various customer needs which will include, but not be limited to: Patient Treatment, Patient Specific QA, development, Software Testing, Troubleshooting, and experimentation.
Troubleshoot PTS equipment including electrical, mechanical, and software problems.
Maintenance of the PTS including but not limited to preventative maintenance and curative maintenance.
Clearly communicate the status of the system to the customer as well as to IBA employees.
Provide support to Software testing and new developments.
Support daily clinical operations for the clinical staff as defined by the specific site manager.
Maintain adequate records as defined by the specific facility.
Support the PTS in all phases which will include but not be limited to: installation, unit testing, integration testing, validation testing and other various site related activities as they are defined by the site manager.
Essential Duties and Responsibilities:
Reporting and record keeping
Builder Account Manager
The Builder Account Manager will develop and maintain relationships with the builder community by training and providing support for current and future projects.
The most important impact this position has on the organization is to sell the decision makers on our goods and services. It is important to have the trust of a developer so that our products are the first choice when decisions are made.
Specific responsibilities include:
Relationship building with development companies and marketing companies. Seeking trends in projects and reviewing features and benefits of our products to follow trends.
Prospecting new projects by working with our retail partners, reviewing permit requests, and by canvassing areas for future development.
Working closely with TSMs to ensure all new accounts are taken care of during and after establishing relationships. Assist in the development of their dealer to builder relationships.
Attending trade shows and social events involving builder trade. Seeking out influential people in the industry to help market our products.
Visiting architect firms and providing education for specifiers on our products.
Visiting job sites as needed
National Builder Accounts Sales Manager
Why Work at Bedrosians
Salary plus bonus opportunity
Full medical, dental, and vision benefits package
Operating since 1948
Family run business
Online new employee training program
National sales territory
Extensive product offerings
Exclusive lines designed in-house
Employee recognition programs
Community giving to Habitat for Humanity
Who You Are
You are highly knowledgeable of the construction and building industry
You have solid contacts with regional and national builders
You develop and grow new and existing partnerships with builders
You are sales-oriented and driven to meet all sales and profit growth plans
You are confident, polished and personable and have a reputation for excellent customer service
You are proactive and creatively think outside the box to grow your business
You are reliable and detail-oriented making sure your customers are satisfied through every step of the process
You are driven to succeed and possess executive planning skills that enable you to do so
You are passionate about our product offerings
You are calm and patient with clients and work well with members of our internal team
What You Need
Ten (10)+ years of sales experience
Five (5)+ years managing builder accounts
Driver's License (must provide current MVR)
Ability to travel nationwide to meet with builder accounts
At Bedrosians, our vision is to be the most customer-centric tile company in the United States.
Bedrosians, our mission is to offer clients a place to buy the most trend-setting tile and stone products available in the market through a seamless purchasing experience.
Bedrosians is an Equal Opportunity Employer that promotes, for the health of its employees, a Drug-Free Workplace philosophy. This job posting does not constitute an offer of employment and is not an employment contract. To be considered for this position please complete our quick 3 minute application through our Careers page: https://bedrosians.applicantpro.com/jobs/
Making better hires starts with building better job descriptions
- Browse 100s of templates across 40+ industries
- Customize your template with your company info & job requirements
- Post it to 20+ job boards in seconds – for FREE!