Dicer Operator Job Description Sample
Cheese Skilled Relief Operator
This position provides coverage for all operator positions in the Cheese Production Department.
All other duties as assigned.
Perform according to Standard Operating Procedures in all Cheese Department Operator positions.
Know all job functions of the Cheese Department Operator positions.
Maintain housekeeping in compliance with Good Manufacturing Practices (GMP's).
Communicate effectively with co-workers, maintenance, quality, and department management.
Follow all required safety practices and procedures.
General Outline of Duties
Covers for the Cheese Department Operators as outlined below:
Cheese Slurry P2 Operator
Prepare start up and shut down process.
Perform cut in and cut out testing for state and document on graph chart.
Monitor seals for leaks.
Perform can checks and calibrate ingredient application system daily.
Verify divert valve is functioning correctly.
Refer to make plan to determine amount of powder, whey cream, water and gluconic acid required.
Adjust set points according to plan.
Direct system based on pounds per hour, set flow rate and monitor flow meters.
Monitor pump speeds, flow rates, pressure and temperature throughout process.
Take samples and test for pH and total solids in DMC lab.
Maintain correct level in Dry Mixer Hold Tank.
Check magnets before start up and at the end of each day.
Communicate with the Cheese Foreperson and follow the Shutdown Calculation Sheet to perform change-overs.
Operate overhead hoist to remove strainers.
Perform CIP processes, making necessary manual connections.
Spray out strainers every 4 hours.
Update Master Sanitation Schedule.
Follow required Lockout / Tagout procedures.
Any additional duties as assigned.
Performs pre-start up inspections.
Controls the mat thickness for consistency by adjusting belt speed, side panels, and vat curd pumps.
Controls dwell time by adjusting belt speed, width, and length.
Controls dicer speed.
Adjusts settings for stir fingers to achieve proper agitation.
Maintains proper positioning of the curd distributors.
Monitors condition of the belt.
Obtains samples to monitor moisture and pH levels, including using a pH meter.
Performs nightly shut-down procedure to prepare for CIP process.
Any additional duties as assigned.
Performs pre-start up inspections
Controls process by adjusting dwell time, temperature, curd density, and water addition
Monitors and trouble shoots process to prevent high fat loss, high fines loss, under melt or over melt functionality, and scrap loss
Maintains optimal agitator speed
Maintains proper curd to liquid ratio
Obtains samples to measure solids using a refractometer
Performs CIP process on tanks between each product code
Performs pre-start up inspections
Measures the amount of fines using a cone test
Maintains optimal auger speed
Adjusts finesaver unit to control consistency of fines
Changes screens regularly to clean and sanitize
Transfers screens to Clean Out of Place (COP) tank
Inspects screens regularly to prevent extraneous
Follow pre-start up procedures and inspections
Operate the wet and dry mixers to a level of proper cheese consistency and feel
Control the curd rate to mixer and auger speed
Maintain proper flow of hex
Control the addition of wet and dry ingredients
Maintain temperature within proper set points
Monitor condition of gaskets and Teflon coating
Take samples and test pH level
Perform can fill check to verify the accuracy of the flow meter
Ensure correct dwell time in the dry mixer
Identify problems with production equipment and troubleshoot solutions
Clear any obstructions
Update records as required
Disassemble equipment for cleaning and make connections for cleaning equipment in place
Understand the operation of the sanitizing system
Perform chemical testing
Keep area clean including sweeping, vacuuming and trash removal
Any additional duties as assigned
Operate equipment to mix blends of dry ingredients according to Make Plan
Coordinate with Cheese Foreperson during changeovers
Maintain inventory levels
Load dry ingredients in major bins
Transfer unused powder to excess bin
Order supplies as needed
Keep are clean including sweeping, vacuuming and trash removal
Any additional duties as assigned
Operate the HTST, vats and CIP system for eight vats simultaneously in a fast paced environment
Communicate clearly with the Quality Department, Cheese Production Operators and department management
React quickly and adjust / troubleshoot equipment to maintain product specifications.
Legibly complete the Make Sheet
Take samples of milk, curd and whey at scheduled times
Understand cheesemaking procedures (i.e.: soft sets, poor acid development, weak curd, and starter problems)
Follow proper agitator RPM's
Perform all necessary checks / calibrations including metering starter and thermometers at designated times
Recognize and communicate potential deviant situations
Start up and shut down HTST
Maintain the plant production schedule
Apply lockouts to equipment as required
Any additional duties as assigned
Operate the HTST, separator and CIP system
Start up and shut down HTST, maintaining compliance with regulatory requirements
React quickly and adjust / troubleshoot equipment to maintain product specifications
Complete Daily Checklists
Handle and test chemicals
Enter data into MES computer system
Monitor and test product quality
Recognize and communicate potential deviant situations
Communicate clearly with the Quality Department, Cheese Production Operators, Whey Production Operators, and department management
Apply lockouts to equipment as required
Any additional duties as assigned
Provide break relief as needed.
Hoses down floor and equipment.
Applies lockouts to equipment as required.
Any additional duties as assigned.
QualificationsGeneral Experience/Educational Background
Must be a minimum of 18 years old.
Must be able to work Sunday - Saturday, off-shifts, weekends, holidays, and required overtime to support a 24 hour/7 day operation.
Must be able to work a minimum of 8.5 hours.
Demonstrated ability to complete work assignments with high degree of accuracy.
Prior manufacturing experience.
Prior cheese and/or dairy foods manufacturing experience.
Three months experience in a cheese operator position within Leprino Foods, Waverly.
Familiarity with SAP or other manufacturing software system working with touch screens.
Language and Technical Skills
Ability to read, write, perform mathematical functions, including a strong mathematical skill set.
Ability to read, write, and communicate effectively.
Accurately operate / calibrate pH meter.
Must be able to maintain accurate records.
Ability to collect samples and provide accurate readings.
Ability to calculate cheese throughput rates.
Ability to calculate pounds per hour to time the distribution of ingredients correctly and prepare the correct amount of ingredients.
Ablility to drive a stand-up hi-lo.
Ability to set priorities.
Able to think clearly under pressure.
Good time management and organization skills.
Ability to work independently without direct supervision.
Exercise good judgment in analyzing problems.
Ability to interpret data and charts and make adjustments to run equipment within specifications.
Physical Demands and Work Environment
This position will be exposed to a production operations environment including both wet and dry production areas with loud noise and varying degress of temperature from freezer to extreme heat.
Specific vision may be required for this position, including close vision, distance vision, color and depth perception, and the ability to read computer screens for extended time periods.
Requires good hand dexterity.
Frequent climbing of stairs, standing and walking.
Must be able to lift and carry moderate weights repeatedly throughout the shift.
Occasional bending and reaching.
Occasional to frequent reaching.
Handles hazardous chemicals.
PBX Operator / Communications Operator / Telephone Operator / Call Center Representative / Receptionist / Customer Service Representative PRN
Medical City Plano
PBX Operator / Communications Operator / Telephone Operator / Call Center Representative / Receptionist / Customer Service Representative
PBX Operator / Communications Operator / Telephone Operator / Call Center Representative / Receptionist / Customer Service Representative processes calls and pages. The Operator takes an active role in communication for emergency codes, conditions, and drills. The Operator also monitors security alarms.
High school diploma/GED preferred
PBX experience preferred
Minimum of two years of heavy multiline phone experience is required
Line Operator - 2Nd Shift
Job Posting Title:
Line Operator - 2nd Shift
ESSENTIAL DUTIES AND RESPONSIBILITIES
This list of duties and responsibilities is not all inclusive and may be expanded to include other duties and responsibilities as management may deem necessary from time to time.
Monitors dough sent from mixer to extruder on overhead conveyor system
Cuts dough with a Chef's Knife and loads the extruder as necessary
Maintains a measured amount of dough inside the extruder hopper
Monitors the dough activity coming out of the extruder. Make recommendations for improvements as needed. Clears dough jams with appropriate procedures and tools as necessary.
Applies flour to the dusting table and top duster.
Monitors the proofing line dough performance. Clears dough jams with appropriate procedures and tools as necessary.
Recommends changes or makes changes to the sheeting process.
Monitors proofed dough by the slitters to ensure proper flow into the chip oven
Monitors chip cutting area for proper size and texture. Make recommendations for improvement if needed
Monitors chip quality after the toaster oven. Makes recommendations for improvement if needed.
Cleans extruder, line/belts, dicer and other areas when the line is down for sanitation.
Scrapes the proofing belts during sanitation.
Removes flour (dusting brush / vacuum) from proofing belts, motors, drives, covers, electrical boxes, and frame during sanitation.
General clean-up of area throughout the day.
Records and documents according to procedures
Communicates with associates routinely to assure that all are aware of the work to be completed, priorities for the day and any impending issues
Performs all plant cleaning and sanitation activities on all equipment and in all departments following both safety and quality procedures, policies, and rules and in accordance with the standards, regulations and laws governing food safety, food quality and environmental safety regulations and monitors and accurately documents all work completed
Assists production with packaging, palletizing, and other duties, as needed
Communicates concerns to Baker, Mixer, and Production Supervisor
Remains current in training expectations
Supports the implementation and monitoring of food safety and food quality standards, regulations, and laws. Notifies leaders if there are any concerns or opportunities for improvement
Keeps work environment clean, safe and positive
Assure the implementation of all identified food quality and food safety standards, laws, good manufacturing practices, training and continuous improvement
Present a good and positive business image in every aspect of your professional daily business
Other duties as assigned
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
Knowledge, Skills and Abilities:
Requires education generally equivalent to a high school diploma
Requires a minimum of one year of progressive work experience preferably food production
Requires a working knowledge of food safety and food quality standards and regulations such as SQF and environmental safety regulations along with a commitment to continuous improvement
Requires basic mathematical skills to be able to add, subtract, multiply and divide combined with the ability to read and interpret formulas and recipes, and calculate proportions, rations and ingredient amounts
Team player, positive attitude, works well with others, and communicates effectively with all associates.
Requires effective and clear written and oral communication skills fluent in English to clearly communicate with other team members
Requires teamwork ability with a positive attitude
Requires moderate computer skills with knowledge of Microsoft programs such as: Word, Excel, PowerPoint and Outlook
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
Frequent use of hands to finger, handle, grasp or touch objects and tools
Frequently is required to talk or listen
Frequent standing, walking, climbing, kneeling, squatting, stooping, crouching, crawling, twisting, bending, reaching
Frequent lift and/or move up to 30 pounds
Occasionally lift and/or move up to 50 pounds, with team lift assistance
Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception and the ability to adjust focus
The employee works indoors in a production environment. Additionally, the incumbent will work near moving mechanical parts, and in high places. He/she will be exposed to fumes or airborne particles. There is moderate noise in the work environment.
TreeHouse Foods is an Equal Employment Opportunity Employer and offers opportunities to all job seekers, including those with disabilities. If you need a reasonable accommodation to assist with your job search or application for employment, please contact us by sending an email to email@example.com. In your email please include a description of the specific accommodation you are requesting and a description of the position for which you are applying.
All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, citizenship, disability or protected veteran status.
Operator Helper - Equipment Operator
Under supervision, perform semi-skilled manual work in connection with an entry level position in power plant operation. Assist equipment operators while learning the following job duties:
Isolate, clean, open, replace, inspect, close and return to service plant equipment. Isolate equipment and place/remove clearance tags in the plant and switchyard. Operate, regulate, adjust, clean and perform minor maintenance on plant auxiliary systems.
Monitor and inspect all plant equipment for normal operation. Identify and report abnormal conditions to the proper authority and write work orders. Operate, clean, service and lubricate portable power driven tools and equipment.
Maintain tools, equipment and work areas in a clean and orderly condition. Utilize portable meters, analyzers and equipment to conduct tests and monitoring. Lubricate and check lubrication equipment; adjust packing glands as necessary and perform necessary operative maintenance, using appropriate hand tools.
Operate oil filtering equipment. Erect and remove simple scaffolding and rigging. Perform routine cleaning of plant areas and equipment, including outside areas, as assigned.
Load, unload, move and handle materials, supplies and equipment; open boxes, barrels, bags and other materials using material handling equipment.
Monitor water chemistry as required. Maintain water pH and follow EPA guidelines as applicable.
Assist in preparing boilers and auxiliaries for operation and removal from service. If applicable, monitor coal feed to mills and burners and observe conditions of fires and furnaces. Hand lance slag in boilers, hand- operating soot blowers, unplugging ash lines, disposing of clinkers and other similar work.
Use flow diagrams to identify system piping and equipment and revise these prints as required. Make required equipment checks and assist in performing tests and preparing related reports, graphs and curves. Perform duties in accordance with Company's safety rules, operating regulations and practices and report unsafe conditions and practices.
Train for and carry out assignments in firefighting, first aid and other emergency response programs as required. Perform other job duties as assigned.
Process Operator - Arodo Mechanic Operator
2nd and 3rd shift positions available
2nd shift position - $1.00/hr shift differential paid
3rd shift position - $2.00/hr shift differential paid
ARODO Mechanic Operator
Safely and efficiently maintain and operate the Arodo packaging line and palletizer.
Maintain the equipment for the Arodo line - all production and maintenance activities. perform mechanical repairs and PM's. Operate various processing equipment.
Read and follow daily production schedule and instructions. Prepare packaging materials by retrieving items from storage, applying labels to container, setting up and loading filling machines, operating various automatic and manual packaging machines, scales and printing devices, industrial lift trucks, pallet jacks and other material handling tools and equipment. Maintain correct weight of the bags produced. Maintain the quality of the bags produced.
Maintain accurate written and electronic records as required by specific tasks. Complete all paperwork - downtime log, used parts, all required QC tests, Shift to shift log book, etc.
Assist in training new operators
Create work order for repair in 7i
Operator Tech I - Wireline Operator
Demonstration of wireline operations technical skills and practical applications, including supporting surveying and wireline logging services, conducting rig-up and rig-down of down hole equipment, disassembly of tools, and post-job on-site equipment testing.
Operate heavy equipment such as Wireline Trucks, Manlifts, Bucket trucks and Forklifts. Support other projects at the Geysers such as performing steam well and pipeline maintenance and assisting with Steamfield and Power Plant operations.
Routine maintenance of wireline equipment at jobsite and assembling tools.
Performing rig-up procedures and installations at jobsites.
Performing safe operation of crane and sling loads.
Performing pre-job preparation of wireline equipment, wireline units, survey jobs and ensuring completion of pre-job logistics.
Removing and disassembling tools and equipment in the field.
Carry out post-job shop responsibilities, including cleaning, servicing equipment, office equipment testing, and accurate and timely submission paperwork and related files.
Preparing and maintaining documentation for jobs, daily reporting, and all applicable administrative functions.
Perform general shop duties for tools and equipment.
Comply with applicable safety standards and maintain a safe working environment
Cooperate with management in promoting, developing and maintaining a safe place of work and safe working practices, meeting all applicable health, safety and environmental requirements
High School Diploma and attendance in trade/vocational school, military service, or equivalent.
Entry level; minimum 2 years directly related experience including understanding of health and safety regulations, and previous experience working with and around hazardous energy, chemicals and waste materials including knowledge of safe handling, storage,
Must have experience with machinery repair.
Must have strong mechanical aptitude and basic understanding of chemistry, physics, electricity and mathematics.
Must have a valid California or other state equivalent Class C license and be in the process of obtaining a Class B license.
Preferred Valid Active Commercial Driver’s License (CDL Class B, Minimum)
Preferred Two years previous experience in wireline and/or geothermal/oilfield industry.
Equal Opportunity Employer of Minorities, Females, Protected Veterans, and Individuals with Disabilities.
Calpine is committed to Equal Employment Opportunity and providing reasonable accommodations to applicants with physical and/or mental disabilities. If you are interested in applying for employment and need special assistance or an accommodation to use
our website or to apply for a position, please send an e-mail with your request to firstname.lastname@example.org. Determination on requests for reasonable accommodation are made on case-by-case basis.
Please view Equal Employment Opportunity Posters provided by OFCCP
Send This Job to a Friend
Machine Operator Entry - VMC Cell Operator - 1St Shift
Good safety, attendance, and performance record
Ablility to interpret shop blueprints
Ablility to interpret MOSs
Ability to do arithmetic and basic shop math
Use standard measuring instruments
Work with minimum supervision
Work well with others
To stay connected with exciting news and the latest job opportunities from GE businesses, follow us on twitter: @geconnections
The Machine Operator Entry
VMC Cell Operator is required to perform each of the tasks below in a safe and timely manner. The Machine Operator Entry
VMC Cell Operator must focus on quality as well as productivity.
As the Machine Operator Entry
- VMC Cell Operator, you will:
Interpret written specs
Perform repetitive heavy lifting
Perform standard work per the quality work plans
Generate improvement ideas on a weekly basis
Participation in team based improvement activities
Activity participate in standard work revisions
Inspect parts using pin / thread gages
Position, adjust, and secure stock or work pieces against stops on chucks, vises, fixtures, or automatic feeding mechanisms
Add coolant and lubrication materials to maintain proper levels
Clean, maintain, and organize assigned area
- High School Diploma / GED
GE is the world's Digital Industrial Company, transforming industry with software-defined machines and solutions that are connected, responsive and predictive. Through our people, leadership development, services, technology and scale, GE delivers better outcomes for global customers by speaking the language of industry.
GE Power is a world leader in power generation with deep domain expertise that helps customers deliver electricity from a wide spectrum of fuel sources. We are transforming the electricity industry with the digital power plant, the world's largest & most efficient gas turbine, full balance of plant solutions and our data-leveraging software. Our innovative technologies and digital offerings help make power and water more affordable, reliable, accessible and sustainable.
GE offers a great work environment, professional development, challenging careers, and competitive compensation. GE is an Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national or ethnic origin, sex, sexual orientation, gender identity or expression, age, disability, protected veteran status or other characteristics protected by law.
Bipro Operator Bipro Operator Th-Sat Every Other Sunday Night 5 Am To 5Pm
Agropur is currently looking for a BiPRO Operator at our Jerome, ID location.
Essential Functions Include the Following:
Operate equipment and control processes in the production of high quality/ high value whey products, while applying learned knowledge of processes involved and production methods.
Complete CIP of the equipment used in the production of high quality/ high value whey products.
Complete all documentation in an accurate and timely manner.
Follow all GMP, SOP and HACCP programs.
Follow all safety programs and procedures directly involved with the whey department.
Monitor processes, materials, or surroundings and reviewing information by telephone, in written form or in person.
Identifying information by categorizing, estimating, recognizing changes or deviations in circumstances and or/events.
Perform operator level maintenance as needed when needed.
Assisting other coworkers with tasks and duties that are within the department as assigned.
Train other/new employees.
Ability to pay strong attention to detail and multitask effectively.
Ability to read and understand SOP's.
Understand and troubleshoot product flow's
Able to properly document information legibly.
Understand and obey all Good Manufacturing Practice.
Previous food production is preferred.
Ability to work in a fast paced environment.
Requires the ability to communicate and document work.
Strong organizational skills.
Good to excellent spelling, grammar and written communication skills.
Track and maintain information on a database.
Intermittently be able to lift 60 pounds.
Be able to move up and down stairs.
Able and willing to work safely with chemicals.
Ability to wear hearing protection.
Able to move above about work stations in a manufacturing environment for a 12 hour shift.
Be able to work at floor level, waist level, and shoulder level repetitively.
Be able to work the shift assigned and fill in other shifts as needed.
Be able to work weekends (including Saturday and Sunday) and off shifts if needed or assigned.
AA/EEO Minority/Female/Disability/Veteran/Sexual Orientation/Gender Identity
Field Operator 2 - Marine Systems Operator
Northrop Grumman's Mission Systems Sector Undersea Systems Division is seeking a self-starting, motivated Field Operator 2 - Marine Systems for an excellent opportunity to join a dedicated team. The team designs, develops, tests, delivers, and operates advanced prototype, unique marine systems.
The qualified candidate will split time working ashore in Southern California and worldwide at-sea aboard commercial work boats. The field site personnel possess a wide variety of engineering disciplines including mechanical, ocean, electrical, and software engineering; drafting; mechanical and electronics assembly; and quality assurance. Candidates for this position are expected to contribute to this broad technical depth with good problem-solving skills and hands-on workmanship abilities. Ashore duties will focus on equipment maintenance and upgrades and operational qualifications and training. At-sea duties will focus on equipment readiness and operations in a high tempo environment.
The Field Operator must be able to work collaboratively in small, technically focused teams; prioritize and adjust tasks simultaneously to accomplish the project result; determine priorities to achieve the required goal on short and long term basis, and make decisions that have an impact on the organization's credibility, operations, and services.
This position is envisioned to be full-time with comprehensive benefits including health and dental insurance, paid time off, and matching contributions to a 401K retirement account. However, qualified candidates who desire part-time/deployment-only employment will be considered and are encouraged to apply. Part-time employees will work at-sea for weeks or months followed by extended time off without pay. Full-time employees will split time between working at-sea for weeks or months followed by working ashore at the Southern California field site.
This position is contingent upon the candidate obtaining a DoD Top Secret Clearance/eligible for SCI access.
High school diploma or GED
Five years of hands-on experience operating and maintaining marine systems, such as remotely operated vehicles (ROVs), autonomous underwater vehicles (AUVs), or diving systems
Ability to work at-sea aboard a commercial vessel. Each at-sea assignment will typically last 45-60 days and employees are generally expected to support at least two at-sea assignments per calendar year. Annual physical exams are required to verify fitness for sea duty.
The chosen candidate be able to obtain and maintain a DoD Top Secret Clearance/eligible for SCI access; this requires US citizenship.
Active Top Secret Clearance/eligible for SCI access is desired.
Bachelor Degree in a STEM field such as mechanical, ocean, or electrical engineering
Prior military experience, preferably U.S Navy
Northrop Grumman is committed to hiring and retaining a diverse workforce. We are proud to be an Equal Opportunity/Affirmative Action Employer, making decisions without regard to race, color, religion, creed, sex, sexual orientation, gender identity, marital status, national origin, age, veteran status, disability, or any other protected class. For our complete EEO/AA and Pay Transparency statement, please visit www.northropgrumman.com/EEO. U.S. Citizenship is required for most positions.
Machine Operator III - Fin Machine Operator
Ensuring Chart's Success…
Chart's manufacturing group is critical to building our products on time and of the highest quality to our customers. The Machine Operator III will work towards our production goals along with peers through the direction of lead man, shift supervisor, and plant manager.
What Your Day-to-Day Activities Will Be…
Candidates will have be running McElroy and Happy fin tube machines
Reads, interprets drawings and written instruction applicable to specific machining process.
Performs set-up and operation as required without supervision.
Performs all required measurements.
Capable of required tool selection for required task.
Trains, or assists in training new employees.
Can safely operate overhead or jib type cranes and rigging.
Performs all non-electrical preventative maintenance as indicated by supervision for specific machinery.
Adhere to all safety guidelines and policies.
Other duties as assigned.
Your Professional Experience Should Be…
- The ability to reading a tape measure as well as blue prints.
Your Education Should Be…
- High School Diploma or Equivalent Work Experience
Your Physical Work Environment Will Require…
While performing the duties of this job, the employee is regularly required to:
Standing for prolonged periods of time.
Occasional repetitive lifting up to 60 lbs as regular daily activities necessitate.
Handle or feel objects.
Tools or controls and talk or hear.
The employee is occasionally required to walk, stoop, kneel, crouch or crawl.
Chart Industries is an equal opportunity employer.
Making better hires starts with building better job descriptions
- Browse 100s of templates across 40+ industries
- Customize your template with your company info & job requirements
- Post it to 20+ job boards in seconds – for FREE!