Furnace Cleaner Job Description Sample
1St Shift Diecast Furnace Technician C - (Db15520)
Full-Time Location: Statesboro, GA
JOB RESPONSIBILITIES Pull samples and run analysis on the Spectrometer Load and flux furnace Check furnace doors Use well walker to skim dross and clean archway Skim off circulation and Degas wells Track aluminum consumption Assist Systems Tech C with launder system Assist Systems Tech B with loading/unloading trucks Daily housekeeping Other duties as assigned JOB SKILLS REQUIREMENTS Basic troubleshooting skills Basic computer skills Technical experience preferred Able to obtain and maintain forklift driving skills and certification EDUCATIONAL REQUIREMENTS High school diploma or GED PHYSICAL AND ENVIRONMENTAL REQUIREMENTS May be required to lift or carry products, parts, and/or other materials of various sizes and weights (Frequently 5 – 25 pounds), (Occasionally 25 –75 pounds), (Rarely 75 pounds) Ability to perform occasional to frequent bending and reaching over a full work shift Ability to stand and/or walk constantly over a full work shift Ability to use power/vibrating tools over a full work shift Ability to operate motorized vehicles over a full work shift Exposure to noise levels for which hearing protection is required to be worn over a full work shift OTHER REQUIREMENTS Completion of Key Train testing upon bidding Disclaimer Briggs & Stratton Corporation, headquartered in Milwaukee, Wisconsin, is the world’s largest producer of gasoline engines for outdoor power equipment.
Its wholly owned subsidiaries include North America’s number one marketer of pressure washers, and it is a leading designer, manufacturer and marketer of power generation, lawn and garden, turf care and job site products through its Briggs & Stratton®, Simplicity®, Snapper®, Snapper Pro® Ferris®, PowerBoss®, Allmand™, Billy Goat®, Murray®, Branco® and Victa® brands. Briggs & Stratton products are designed, manufactured, marketed and serviced in over 100 countries on six continents. Briggs & Stratton Corporation is committed to a policy of equal employment opportunity.
The Company conducts all employment practices without regard to race, sex, color, religion, national origin, age, disability, protected veteran's status, pregnancy, genetic information, sexual orientation or any other basis prohibited by law. Briggs & Stratton also undertakes affirmative action to assure equal employment opportunity for minorities and women, for persons with disabilities, and for protected veterans.
Heat Treated And Brazing Furnace Operator
Aerojet Rocketdyne is a world-recognized aerospace and defense leader providing propulsion and energetics to its space, missile defense, strategic, tactical missile and armaments customers throughout domestic and international markets. We are seeking a
Heat Treating and Brazing Furnace Operator for our Canoga Park, CA facility to work either the 1st or 2nd shift. This is a Union position.
Set up and operation of Heat treating and controlled atmospheric brazing furnaces to braze rocket engine thrust chambers and other assemblies where vacuum, explosive and/or inert gas atmospheres are used in production. Essential Job Functions (Including % of Time for Each) 100%- Plan brazing and/or heat treat operations of developmental, prototype and production assemblies in controlled atmospheric brazing furnaces where explosive and inert gasses are used in the atmospheres. Set power and temperature controls, gas flow panels and instrumentation for electric or gas fired furnaces. Adjust switches on temperature control instruments for multiple cycle brazing.
Load assemblies on furnace base and make hookups of thermocouples and pressure lines as required.
Operate auxiliary power equipment to unload furnaces and cool down with cooling muffles. Perform heat treating and/or brazing operation as required.
Operate furnace to heat treat and/or braze assemblies including leak check and purge, instrumentation, heat-up, braze and cool down. Take action when emergency conditions arise during phases of operations to assure safety of personnel and equipment. Over-ride furnace controls by manual operation when necessary.
Requirements High school diploma or equivalent and five (5) years of experience in heat treating and brazing operations.
Demonstrated experience working with and around hazardous chemicals including acids.
Must have a proven safety record and experience with PPE used with hazardous chemicals.
Experience handling large (500 lbs +) complex hardware with tooling and other handling devices (ie: pallet jacks, cranes, lifting straps, etc).
Experience reading, comprehending and using planning and drawings to meet required specification requirements.
Experience using measurement instruments to ensure parts are set-up and indicated properly to meet requirements.
Must carry or obtain applicable certifications to work in an environmentally controlled room.
- Must pass the written and practical exam required for Heat Treated and Brazing Furnace Operator. US Citizenship required. Must also be able to satisfy federal government requirements for access to government information, and having dual citizenship may preclude you from being able to meet this requirement. Work Environment and Physical
The work environment may require a combination of indoor and outdoor activity (hot, cold, wet, humid conditions) with a varied amount of walking, standing, sitting, climbing (i.e. ladders, stair, scaffolding, ramps), balance (maintaining body equilibrium to prevent falling when walking, standing, or crouching on narrow, slippery, or erratically moving surfaces), bending, reaching, handling/fingering (seizing, holding, grasping, turning picking, pinching), stooping, kneeling, crouching and ability to lift/carry/push/pull up to 50 pounds. Work may require the ability to operate material handling equipment (forklift, crane, hoist, man lift, etc.) in a safe manner. While performing the duties of this job, employees may work around variable noise levels or with fume or airborne particles, hazardous chemicals, etc. requiring the use of personal protective equipment such as face protection (safety glasses, goggles, face shield), foot protection (i.e. steel toed shoes, rubber boots, etc.), gloves, hard hat, shop coat and hearing protection.
Some positions may require Respirator clearance up to and including the Self Contained Breathing Apparatus (SCBA) Level A clearance. Work requires the ability to change into or out of personal protective equipment when entering or exiting manufacturing, laboratory, or other areas. Some employees may be required to drive between various locations within the Company facility or between locations.
Work duties may also be required to work in a standard office setting and to use standard office equipment, including a computer and/or the ability to travel by air or auto. Ability to distinguish colors may also be necessary. This position may be expected to work varying shifts and hours to ensure successful operation of activities in the organization. Need help finding the right job? We can recommend jobs specifically for you!
We consider the consistent demonstration of positive, cooperative, self-motivated, courteous and professional behavior to be an essential function of every position. While different positions have different primary areas of responsibility and technical expertise, everyone needs to work as a team, and we expect all employees to contribute as necessary to get the job done. Unless otherwise stated in the requirements section of an individual job listing, our positions require U.S.
Citizenship, U.S. Permanent Residency, or other status as a U.S. Person as defined by 8 USC 1324b(a)(3). Equal Opportunity Employer/Minorities/Females/Veterans/Disability.
Individuals with a disability requiring accommodation during the application and/or theinterview process should e-mail the Human Resources Department at
CategoryManufacturing and Production - Other
Hot Punch Furnace Operator
Job Description General
This is a job summary which includes essential job duties of the position. More specific information regarding duties may be provided upon request. In this role the selected person will need to have a good time management skills due to running 4 furnaces at once. The selected person will need to be able to work in a team environment and have a strong understanding of 5s and TPM. Duties: * Learn to operate multiple pieces of equipment including a horizontal furnance, butt welder, punch press.
Work as part of a team to identify quality and production gaps in the operation of new
Flex hours/schedule as demand dictates
Participate in safety initiatives.
Meet customer quality and production needs.
Utilize SAP for transactions, Inventory control
Willing to cross train on multiple pieces of equipment. Climate: Position requires highly motivated individual that can work in a rapidly changing manufacturning environment. Work is conducted in an environment of management and factory skilled and non-skilled personnel, with special emphasis on practicing team principles.
* Will to be hands on with equipment troubleshooting and process improvements
Good analytical and problem solving skills
Some computer ability
Good mathematical ability Hours:(1) M-F 5p-5a (2) A/B 5a-5p
EEO Statement All qualified applicants to Stanley Black
& Decker are considered for employment without regard to race, color, religion, age, sex, sexual orientation, gender identity, national origin, disability, veteran’s status or any other protected characteristic.
Requisition Number: 49053BR
City:* East Longmeadow
Business:* US - GTS - Hand Tools Accessories and Storage (HTAS)
Project Manager – Furnace Engineer
Relocation assistance is available for those who qualify under our relocation policy.
-Create safe processes and specification of equipment, ensures that ergonomics is considered in all areas of design, and that potential safety and health hazards are identified and eliminated during project execution.
-Ensure that all safety policies and procedures are followed, driving a zero-incident project environment.
-Design of environmentally compliant processes and specification of environmentally compliant equipment, ensures that all permit requirements are considered and addressed in the design, and that potential environmental issues are identified and addressed during project execution
- Develop scopes, specifications, schedules, and investment grade cost estimates for multi-discipline industrial manufacturing capital projects worldwide up to $10M
- Develop, guide, review, and present project feasibility studies and business cases that accurately identify project benefits, risks, and returns
- Utilize glassmaking furnace experience to guide projects to cost effective, best practice, designs to ensure successful project with respect to quality, technology, cost, and schedule.
- Utilize working knowledge of refractory properties/applications to ensure optimal refractories are used in projects to meet life expectancy and financial goals
- Utilize working knowledge of glassmaking operations to assist with ongoing furnace life expectancy issues and hot repair requirements.
- Develop technical specifications and contracts for equipment and services for all aspects of projects and ensure compliance.
- Coordinate, review, provide oversight and manage external engineering resources and consultants and contractors as needed to meet project objectives
- Bachelor's degree in engineering, preferably mechanical, electrical, chemical or materials engineering
- Minimum of 6 years engineering experience in an industrial or manufacturing industry
- Demonstrated success managing projects up to $10M
- Strong project management skills
- Knowledgeable of the supply chain process, bidding, evaluating, contractor selection, and risk mitigation to JM through smart contracting
- Must be able to work on multiple projects simultaneously in different phases
- Heavy travel required (50-75% travel)
- Experience with glassmaking furnaces and/or forehearths.
- Demonstrated knowledge and experience with large manufacturing furnaces and/or glassmaking operations.
- Working knowledge of refractory properties/applications and uses for both cold rebuilds and hot repair applications strongly preferred.
- PMP Certification
- Experience in fiberglass or glass manufacturing industries
Seeking experienced furnace installer
Business Unit Group:
Engineered Products and Solutions
Position Description: Arconic Engines is a world-class producer of aero engine and industrial gas turbine components, including airfoils, rings, disks and forgings. We excel in vacuum melted superalloys, machining, performance coatings and hot isostatic pressing for high performance parts that enable the next-generation of quieter, more fuel-efficient aero engines and cleaner power generation. Arconic Engines is a business unit of Arconic (NYSE:ARNC). Join Arconic and join a network of people who are passionate about industry-changing technology that advances the world. You’ll have the opportunity to work with leading global companies that operate in world-changing industries—such as aerospace, automotive, building and construction, defense and commercial transportation. It’s not just a job. It’s a career and a path to the future. You’ll be part of a diverse culture of learning, teaching and mentorship. Arconic is fully committed to developing people: providing employees with the resources, and learning and development opportunities they need to excel and build a career.
SUMMARY The furnace technician will be responsible for performing repairs, preventative maintenance, Temperature Uniformity Surveys (TUS), System Accuracy Tests (SAT) and furnace control instrument calibrations. Troubleshoot and repair furnace instruments and combustion systems to maintain operation of furnaces in a Quality environment in accordance with quality compliance procedures.
ESSENTIAL DUTIES AND RESPONSIBILITIES : This is not intended as a comprehensive list; it is intended to provide a representative summary of the major duties and responsibilities. Incumbent(s) may not be required to perform all duties listed, and may be required to perform additional, position-specific tasks.
Provide maintenance and repair services for Hot Work production furnaces and Heat Treat furnaces.
Sound understanding of combustion theory and application of concepts during furnace troubleshooting and repair to maintain thermal furnace characteristics and operational efficiency.
Prepare survey racks and stands for the performance of Temperature Uniformity Surveys to include: cutting and welding thermocouple wire to the required length(s) and affixing them to the correct positions on the survey rack / stand(s) in accordance with quality procedures.
Perform Temperature Uniformity Surveys test using a Portable Survey Datalogger Field Test Instrument mobile computer.
Upload the Temperature Uniformity Survey results to the network system for proper review and acceptance by the Quality personnel in order to release the furnace back to production following the performance of Temperature Uniformity Survey or System Accuracy Test.
Calibrate furnace control instruments such as the temperature chart recorders, temperature controllers and the over limit controllers.
Create the certification of calibration for each instrument and affix calibration sticker that shows calibration date and due date in accordance with quality procedures.
Work directly with the Quality Department representatives, supervision and management to immediately identify and correct issues affecting the compliant functioning of furnaces.
Assuring that after the quality personnel reviews and approves the certification of calibration file calibration records with the maintenance planner.
Validate and confirm sufficient furnace components are on hand for the performance of scheduled TUS, SAT and calibrations.
Ensure that all the instruments that can not be calibrated in house get calibrated by an outside source, such as Optical pyrometers, potentiometers and gas analyzers.
Review material certifications to ensure they have been approved for release and use by the Quality Department for thermocouple wire, control thermocouples, potentiometers, optical - pyrometers and Gas analyzers prior to their usage for both Forge and Heat Treat Departments.
Knowledge of Programmable Logic Controllers and electro-mechanical controls a must.
All these duties are performed in accordance with Spec. AMS2750 Pyrometry latest revision.
Requisition Number: 21020BR
Minimum Years of Experience: 5
Primary Location: CA-Rancho Cucamonga
Minimum Education Required: High School or GED
Minimum Travel Required: None
High school diploma Five to Seven years related experience and/or training; or equivalent combination of education and experience
Employees must be legally authorized to work in the United States. Verification of employment eligibility will be required at the time of hire. Visa sponsorship is not available for this position.
This position is subject to the International Traffic in Arms Regulations (ITAR) which requires U.S. person status. ITAR defines U.S. person as an U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee.
Business Unit: Arconic Engines
Job Type: Experienced Compliance With the Equal Employment Opportunity and Affirmative Action Laws and Regulations Arconic reaffirms its policy to provide equal employment opportunity in recruiting, hiring, upgrading and promotion, conditions and privileges of employment, company-sponsored training, access to facilities, educational assistance, social and recreational programs, compensation, benefits, transfers, discipline, layoffs, recalls or termination of employment to all employees without discrimination because of race, color, religion, national origin, disability, sexual orientation, gender identity / expression, veteran status, genetic information, sex or age (within statutory limits). We live our Values and measure our success by the success of our customers, shareholders, communities and people. Arconic’s success is driven by the advantage created by the collective efforts of its employees, and is dependent upon a diverse, inclusive environment that embraces change, new ideas, respect for the individual and fosters an equal opportunity for success. We have zero tolerance for discrimination, intimidation or harassment of any kind.
Manufacturing Engineer (Vacuum Furnace Processing)
Manufacturing Engineer (Vacuum Furnace Processing) Manufacturing and Production - Engineering Apply for this position SpaceX was founded under the belief that a future where humanity is out exploring the stars is fundamentally more exciting than one where we are not. Today SpaceX is actively developing the technologies to make this possible, with the ultimate goal of enabling human life on Mars. MANUFACTURING ENGINEER (VACUUM FURNACE PROCESSING) As a Manufacturing Engineer at SpaceX you will have the opportunity to utilize your knowledge, experience and creativity to develop novel solutions at the cutting edge of space technology. You will work on systems that will ferry humans to and from the International Space Station and ultimately extend humanity’s reach beyond the earth and moon. You will own the relationship between our development and production teams. You will provide input into the design and development of new and existing hardware and take a lead role in manufacturing and integration on our current and next generation vehicles. RESPONSIBILITIES:
Support the production, assembly, and integration of the area products
Aggressively drive and implement process improvements to reduce assembly hours and build cost
Fully develop and implement future state production systems for all products
Create capital/facility justifications for large projects and manage through implementation and runoff
Oversee all process functions, document control, and continuous improvement within furnace/heat treat processes as assigned
Develop PFMEA’s, control plans, work instructions, and specifications
Lead in the development of proper heat treat cycles for new components or material
Establishing metrics and data that displays the health of all production parts and equipment
Create and maintain maintenance schedules for all related equipment. This Engineer will also assist in the maintenance of the equipment as necessary to keep production at rate
Design, analyze, create and test new tooling for all heat treat operations as needed
Assist in the design of new components for proper braze joint configurations (DFM)
Manage the transition of each related production area from dev processing to full rate production
Training technicians on a range of operations including:
Braze and heat treat operations according to spec
Set up and operation of hardware in vacuum furnaces and install T/Cs according to spec BASIC QUALIFICATIONS:
Bachelor's degree in mechanical, aerospace, metallurgy, welding, systems or manufacturing engineering + 2 years of experience in a heat treat or manufacturing facility, running, maintaining and developing processes/equipment
Lean manufacturing training or experience PREFERRED SKILLS AND EXPERIENCE:
Master's degree in mechanical, aerospace, metallurgy, welding, systems or manufacturing engineering + 5+ years of experience in a heat treat facility, running, maintaining and developing processes/equipment
Experience with technical review of materials processing and a sound understanding of the interaction between process variables and the resulting microstructure and properties
Pareto analysis, root cause and corrective action experience
Experience with the development of products from R&D into production
Process development, facility and line layouts, PFMEA, error-proofing
Knowledge of metallic or composite manufacturing techniques, processes, equipment and other processes such as: machining, welding, drilling, sheet metal forming and stamping
Participation in AWS, SAE/AMS, ASME or ASTM committees
Design for manufacturability and assembly
Knowledge of the basic principles of chemistry, engineering, fluid dynamics and mechanics of materials
Design and analysis (Finite Element Analysis (FEA)/structural/static loads) experience
Experience with capacity modeling, process mapping and fault analysis
CAD experience (NX & Teamcenter a plus)
Geometric Dimensioning and Tolerancing (GD&T) experience ADDITIONAL REQUIREMENTS:
Position may require long hours and weekend work ITAR REQUIREMENTS:
To conform to U.S. Government space technology export regulations, applicant must be a U.S. citizen, lawful permanent resident of the U.S., protected individual as defined by 8 U.S.C. 1324b(a)(3), or eligible to obtain the required authorizations from the U.S. Department of State. Learn more about ITAR here. SpaceX is an Equal Opportunity Employer; employment with SpaceX is governed on the basis of merit, competence and qualifications and will not be influenced in any manner by race, color, religion, gender, national origin/ethnicity, veteran status, disability status, age, sexual orientation, gender identity, marital status, mental or physical disability or any other legally protected status. Applicants wishing to view a copy of SpaceX’s Affirmative Action Plan for veterans and individuals with disabilities, or applicants requiring reasonable accommodation to the application/interview process should notify the Human Resources Department at (310) 363-6000. Job Location Hawthorne, CA, United States
Vacuum Furnace Operator- 2Nd Shift
Eaton’s Power Systems, Electrical Sector – Americas, has one opening for a 2nd shift Vacuum Operator in our Vacuum Lab in South Milwaukee. The selected candidate will be responsible for set-up, adjustment, and operation of all departmental equipment. This includes operation of electro polishing, silver plating, hydraulic presses, spot welders, and braze furnace equipment, and other operations performed as a vacuum operator. Typical Duties:
Assemble Vacuum Bottles
Electro-polish Stainless Steel, Copper, & Monel
Perform hipot, length, pressure & resistance tests
Operate Silver Plating
Load, Unload, and Operate the Furnace
Pre-braze & Spot Weld
Knowledge of Hazardous Materials & their Locations
Read & use Production Documentation including Blue Prints
Notify department team leader / lead operator / supervisor / manager (escalation process) of all material and/or equipment deficiencies.
Interface with other departments as production requires (Engineering, Quality, etc.)
Meet or exceed quality and quantity standards.
Keep work area clean and orderly.
Contribute suggestions for methods or product improvement.
Use and operate tools and equipment consistent with this job.
Perform other related duties as assigned.
Adheres to all environmental, health, safety rules and regulations, and work instructions.
Fosters an environment that promotes Eaton’s goals, philosophies, and encourages continuous improvement through participation and teamwork. Qualifications Basic Qualifications
Must be legally authorized to work in the United States without company sponsorship.
No relocation benefit is being offered for this position. Only candidates that currently reside within the immediate geographical area (50 miles) of the work location will be considered.
Must have a high school diploma or GED from an accredited institution.
- Minimum of 1 year of relevant experience.
• 2 or more years of experience working in a manufacturing environment. We make what matters work. Everywhere you look—from the technology and machinery that surrounds us, to the critical services and infrastructure that we depend on every day—you’ll find one thing in common. It all relies on power. That’s why Eaton is dedicated to improving people’s lives and the environment with power management technologies that are more reliable, efficient, safe and sustainable. Because this is what matters. We are confident we can deliver on this promise because of the attributes that our employees embody. We’re ethical, passionate, accountable, efficient, transparent and we’re committed to learning. These values enable us to tackle some of the toughest challenges on the planet, never losing sight of what matters. Job: Manufacturing & Operations Region: North America – US/Puerto Rico Organization: ESSG CPSD PRD Power Reliability Division Job Level: Entry Level Schedule: Full-time Is remote work (i.e. working from home or another Eaton facility) allowed for this position?: No Does this position offer relocation?: No Travel: No Eaton is an Equal Opportunity and Affirmative Action Employer. Eaton is committed to ensuring equal employment opportunities for all job applicants and employees. Employment decisions are based upon job-related reasons regardless of an applicant's race, color, religion, sex, sexual orientation, gender identity, age, national origin, disability, marital status, genetic information, protected veteran status, or any other status protected by law.
Hand loads specified proportions of scrap metal and returns to furnace.Sprinkles fluxing compound on molten metal to bring impurities to the surface.Turns valves to regulate injection of fuel and air into furnace, or moves controls to regulate flow of electricity and water coolant through electrodes to heat furnace to specified temperature.Observes color of metal and instruments such as voltmeter, ammeter, wattmeter and pyrometer.Removes crucible containing molten metal from furnace, moves levers to tilt crucible or open crucible door, or breaks clay plug to pour metal into ladle for transportation to molds.Skims slag from surface of molten metal.Transfers molten metal from furnace to teapot ladle.Covers open risers and sprue with hot top as soon as pourers fill a mold.Pours molten metal in sand molds when needed.Cleans furnaces and equipment.Must be able to figure furnace and ladle additions if lead man is not available (vacation or emergency).Be able to do minor repairs i replace furnace leads or hydraulic lines.Inspect inside of furnace after each pour for thin spots in lining and make decision if it is safe to run.Help set up heats and write mold (casting) numbers and quantity poured in the heat.Tag heat with heat number and material.Help shake out heats.Watches melt scrap for quality.Relines furnaces when the linings become unsafe.Insures the tap temperature is correct for the type of metal being poured and for the size and configuration of the casting in the mold.Must operate forklift and skid loader.Responsible for prepour and final coupons for spectrograph analysis.Operates electric hoist to assist in loading or moving materials and products.Performs all work in a safety conscious manner. Be aware of dangers and take all appropriate counter measures to protect yourself and others around you.Wear all PPE that is required.
Ear plugs, respirator, face shield, apron, sleeves, leggings and steel toe boots.Responsible to maintain a clean and safe work area consistent with the Companyis housekeeping policies.Hampton Hydraulics, LLC, dba Seabee, a Ligon Company, recommends the National Career Readiness Certificate. For information on how to obtain this certificate, contact your local IowaWORKS office.
Title: Furnace Engineer Location:
US-US-TX-Houston Job Number: 1058801 KBR COMPANY INFORMATION When you become part of the KBR team, your opportunities are endless. As a leading global engineering, construction, and services company, we support the hydrocarbon and government services markets on six continents. Serving our customers through diverse business units, we offer challenging assignments on some of the world's largest and most complex projects where our customers have come to value us, because they know We Deliver.
Join us and you'll be part of a dynamic, elite team of professionals who understand what it takes to get a job done and has the experience, knowledge and determination to succeed. Position Title: Furnace Engineer Position Description/Job Responsibilities Under direct supervision, independently evaluates, selects, and applies standard engineering techniques, procedures, and criteria, using judgment in making minor adaptations and modifications to furnaces.
With additional experience within one functional area, assists in the design of larger and more complex designs which involve complex features for which there are precedents. Job tasks required development of specifications and data sheets for furnace related equipment such as burners, fans, heat transfer devices etc. Interaction with Suppliers of such equipment is required.
Qualifications: Requirements/Qualifications Undergraduate degree in Engineering Minimum of 2 years related experience Typical experience ranging from 3-7 years B ENEFITS KBR offers a selection of competitive lifestyle benefits which could include a 401K plan with company match, medical, dental, vision, life insurance, AD&D, flexible spending account, disability, paid time off, or flexible work schedule. We support career advancement through professional training and development. KBR is an equal opportunity employer.
All qualified applicants will receive consideration for employment without regard to race, color, religion, disability, sex, sexual orientation, gender identity or expression, age, national origin, veteran status, genetic information, union status and/or beliefs, or any other characteristic protected by federal, state, or local law. Job: Engineering
Making better hires starts with building better job descriptions
- Browse 100s of templates across 40+ industries
- Customize your template with your company info & job requirements
- Post it to 20+ job boards in seconds – for FREE!