Needle Grinder Job Description Sample
Needle Utility Operator
Ethicon, Inc., a member of Johnson & Johnson's Family of Companies, is recruiting for a Micro Needle Utility Operator located in Somerville, NJ.
The Ethicon Surgical Care business offers a broad range of products, platforms and technologies—including sutures, surgical staplers, clip appliers, trocars and synthetic mesh devices—that are used in a wide variety of minimally invasive and open surgical procedures. Specialties include support for treatment of colorectal and thoracic conditions, women's health conditions, hernias, cancer and obesity. The Ethicon Surgical Care business combines products and services of two market-leading legacy companies, both with long histories of medical innovation. Ethicon, Inc. based in Somerville, New Jersey, was founded more than 80 years ago as a pioneer in suture development and manufacturing, helping to transform the safety and effectiveness of open surgery. Ethicon Endo-Surgery, Inc. was created 20 years ago in Cincinnati, Ohio, developing innovative devices that have driven the revolutionary shift from open to minimally invasive surgery that continues to lead the industry today.
The Micro Need Utility Operator under general supervision and in accordance with applicable specifications, polishes, inspects, and heat¬ treats micro and channel needles in various alloys. Keeps equipment and work area clean and orderly. Does all other work, related in nature to assure efficient machine operation and maintenance of production schedule.
Be responsible for compliance to FDA/GMP/ISO/OSHA as it pertains to daily activities within Ethicon.
Follow all job specific safety procedures and utilize PPE when necessary.
Comply with quality system requirements as defined within procedures. and instructions and enter production information in quality records.
Use test equipment (Starrett Gauge, Mitutoyo Gauge, Microscope etc.) where applicable.
Utilize applicable software systems as needed for the job (e.g. JDE, ComplianceWire, ADAPTIV,etc.)
Be familiar with proper documentation practices and SOPs.
Consistently meet required work performance targets (RE's), if applicable.
Support LEAN and Six Sigma Initiatives.
This position pays $25.66/hour and is under a Collective Bargaining Agreement in a union environment.
A minimum of a High school diploma or G.E.D. is required.
Experience in an FDA regulated environment, required.
Knowledge of GMP (Good Manufacturing Practices) and GDP (Good Documentation Practices) is required.
Basic computer skills and problem-solving ability is required.
Basic math skills: add, subtract, multiply, divide, percentages, shop arithmetic, decimals, fractions, etc., required.
Experience utilizing JDE is required.
Ability to read and interpret needle specifications, process specifications and simple shop drawings is required.
Dexterity to hang needles on racks, inspect needles under a microscope, and the ability perform repetitive hand motion and fine manipulation is required.
Ability to perform trouble shooting is required.
Must be able to work with chemical and fumes.
Ability to perform batch change over for machine is required.
This position requires a daily commute to Somerville, NJ, Monday - Friday for the 1st shift working hours of 6:00AM - 2:30PM with occasional overtime and off-shift hours, including weekends, is required.
Shingle Grinder Operator - Prescott
Shingle Grinder Operator - Prescott
Location: Lebanon, PA, US, 17042
Company: Pennsy Supply Inc
Job ID: 133747
Pennsy Supply, part of Oldcastle Materials, Inc., a division of Oldcastle, is the leading vertically integrated supplier of aggregates, asphalt, ready mixed concrete, and construction and paving services in the United States. Our operations span the nation from Montana to Texas and from Washington to Florida, with 17,500 employees at more than 1,200 locations in 44 states.
This position is responsible for operating and maintaining the shingle-grinding machine safely and efficiently
Essential Duties and Responsibilities
Perform pre-shift inspection on shingle-grinding machine
Perform maintenance on equipment
Weld & use torch on grinding machine as necessary
Operate front-end loader & other equipment
Maintain and repair grinding machine on a daily basis
Help with stone, concrete, and asphalt plants as needed
Other duties as assigned
Education and/or Experience
- Welding and torch experience is helpful, but not mandatory
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required.
Must pass a drug screen and criminal background check
Able to work independently with attention to detail
Able to follow direction and work effectively in a team environment
Able to respond to stressful situations and customers in a professional, courteous manner
Ability to effectively prioritize assignments to meet long-term and short-term deadlines
Excellent organizational skills
Able to work various times during day, night or weekend hours, at various locations
What Oldcastle Offers You
A culture that values opportunity for growth, development and internal promotion
Highly competitive base pay
Comprehensive medical, dental and disability benefits programs
Group retirement savings program
Health and wellness programs
Oldcastle has a long and proud heritage as one of North America's largest corporations. We are a proud reflection of the hundreds of family businesses, local and regional companies and mid to large sized enterprises that together form the Oldcastle family. Oldcastle operates with a decentralized, diversified structure, letting you work in a small company environment while having the career opportunities of a large enterprise.
Oldcastle is a great place to grow! If you're up for a rewarding challenge, we invite you to take the first step and apply today! Please complete your online application and profile which will be sent directly to the appropriate Hiring Manager. Thank you for your interest in the Oldcastle family!
Follow Oldcastle Careers on Facebook, Twitter, Instagram, Google+, Pinterest, WordPress (Career Blog) and LinkedIn!
Oldcastle Materials is an Affirmative Action and Equal Opportunity Employer.
EOE/Vet/Disability--If you want to know more, please click on this link.
Oldcastle Materials is part of the Oldcastlecareers™ network.
Nearest Major Market: Harrisburg
Job Segment: Welding, Equipment Operator, Supply, Front End, Manufacturing, Operations, Technology
Trinity Marine Products is searching for a Grinder in our Caruthersville, MO barge plant.
Trinity Marine Products, Inc. (TMP) is a leading U.S. manufacturer of barges that transport dry and liquid cargoes on inland waterways.
TMP manufactures tank barges that carry petroleum and other refined products, chemicals, fertilizer, ethanol, and other liquid cargoes.
TMP also manufactures dry cargo barges, including flat-deck and hopper barges that transport a variety of products, such as grain, coal, and
What You'll Do:
Clean all tanks of debris, testing water, grinding and welding burrs
Use torch and air arc
Perform all duties within acceptable time standards
Comply with all company safety rules and procedures
Perform generalhousekeeping/clean up in assigned work area
Perform other similar or related work as assigned
Shift Schedule: 6:00 AM - 4:00 AM, Monday - Thursday
What You'll Need:
Basic knowledge of hand tools
Prior experience working in a construction, industrial, or manufacturing environment is beneficial
Previous experience operating a grinder, a torch, and/or air arc is preferred
Able to work above ground (10 ft or more)
Must be able to climb ladders or stairs to reach objects; comfortable with heights
May require working in narrow or confined work spaces for extended periods of time
Tasks may require physical strength and dexterity for lifting
May require extensive kneeling, bending, walking and/or standing for long periods of time
Able to work effectively while wearing the required PPE
Regular and predictable attendance is required
This position is responsible for operating machinery to ensure the continuous flow of product thru the production process. Responsible for monitoring and adjusting machine settings as needed and notifying supervisor if machines should require maintenance while maintaining a safe work environment and adhering to Tyson policies and procedures.
This position requires assisting the main machine operator in his her duties, loading and unloading the machines, keeping work area clean, record purchase orders, temperatures, and other information as directed by their supervisor. Position requires proper inspection of vats used in the process.
Also requires mixing ingredients according to customer recipes, and must be willing to lift products up to 70 in lbs in weight. Also involves opening bags of ingredients and pouring into bins for batching. Position performs periodic inspections of equipment to ensure proper operation.
Jobs are fast pace and require repetitive motion. Position will work in cold environment with temperatures of at least 40 degrees and also a wet environment.
This facility works 7 days a week Sunday - Saturday. Must be willing to work weekends and overtime as necessary.
Willing to accommodate shift start time changes as necessary. All job offers are based on the conditions that the candidate can provide proof of authorization to work legally within the US and pass a urinalysis screening which is part of the post-offer health assessment.
Tyson Foods, Inc. voluntarily participates in the E-Verify system and uses all tools made available by the federal government to confirm the employment eligibility of all team members. Persons offered employment with Tyson Foods are required to provide documentation proving their employment eligibility, and all offers of employment are contingent upon successful completion of the E-Verify process.
Grinder Machinist (2Nd Shift)
Aerojet Rocketdyne is an innovative company delivering solutions that create value for its customers in the aerospace and defense markets. The company is a world-recognized aerospace and defense leader that provides propulsion and energetics to the space, missile defense and strategic systems, tactical systems and armaments areas, in support of domestic and international markets. Additional information about Aerojet Rocketdyne can be obtained by visiting our websites at www.Rocket.com and www.AerojetRocketdyne.com.
We are seeking a Grinder Machinist to join our facility in Canoga Park, California (Los Angeles area). Union position. 2nd shift.
Essential Job Functions (Including % of Time for Each)
Read and interpret information from planning documents, drawings, blueprints, sketches, specifications, charts, graphs and engineering orders to develop machining/grinding operations and tooling.
Calculate dimensions, reference points and lines, radii and angles using shop math, including geometric and trigonometric formulas.
Based on drawing requirements and the grinding characteristics of various metals, ceramics, plastics and composites, select the appropriate grinding tools, wheels, speeds and feeds.
Setup and operate various grinding/lapping machines to perform any operation within the capacity of the machine.
Visually and with the aid of precision measuring instruments check work for accuracy of dimensions and surface finish.
Record manufacturing data and statistics manually or with the aid of a personal computer.
High school diploma or equivalent preferred.
Preferred 3 years' experience operating NC/manual milling or grinding machine tools/wheels. Depending on experience will accept 5 years experience on 4 and/or 5 axis CNC Mills.
Must have a proven safety record.
Working knowledge to be able to operate various types of conventional, and computer numerically controlled machines.
Working knowledge of grinding wheels, including the dressing, trimming, and forming of wheels to change shape of the wheel, metals and components.
Experience reading and interpreting information from planning documents, drawings, blueprints, sketches, specifications, charts, graphs and engineering orders to plan and check the planning of operational sequences and methods.
Experience using precision measuring instruments to check work for accuracy of dimensions and surface finish.
Ability to use electronic work instructions, specifications, and drawings to meet customer requirements.
Skilled at using precision hand tools, micrometers, indicators, Jo blocks, gages etc. to ensure parts are set-up and ground to meet blueprint requirements.
Working knowledge of basic shop math, geometry, trigonometry for determining speeds/feeds, part reference points, angles and positions.
Familiarity with Geometric Dimensioning and Tolerancing (GD&T).
Ability to follow work instructions, manage time efficiently and get along with co-workers.
US Citizenship required. Must also be able to satisfy federal government requirements for access to government information, and having dual citizenship may preclude you from being able to meet this requirement.
The work environment may require a combination of indoor and outdoor activity (hot, cold, wet, humid conditions) with a varied amount of walking, standing, sitting, climbing (i.e. ladders, stair, scaffolding, ramps), balance (maintaining body equilibrium to prevent falling when walking, standing, or crouching on narrow, slippery, or erratically moving surfaces), bending, reaching, handling/fingering (seizing, holding, grasping, turning picking, pinching), stooping, kneeling, crouching and ability to lift/carry/push/pull up to 50 pounds. Work may require the ability to operate material handling equipment (forklift, crane, hoist, man lift, etc.) in a safe manner. While performing the duties of this job, employees may work around variable noise levels or with fume or airborne particles, hazardous chemicals, etc. requiring the use of personal protective equipment such as face protection (safety glasses, goggles, face shield), foot protection (i.e. steel toed shoes, rubber boots, etc.), gloves, hard hat, shop coat and hearing protection. Work requires the ability to change into or out of personal protective equipment when entering or exiting manufacturing, laboratory, or other areas. Some employees may be required to drive between various locations within the Company facility or between locations. Work duties may also be required to work in a standard office setting and to use standard office equipment, including a computer and/or the ability to travel by air or auto. Ability to distinguish colors may also be necessary. This position may be expected to work varying shifts and hours to ensure successful operation of activities in the organization.
McConway & Torley, LLC, a Trinity Industries business, is a leading manufacturer of railcar coupling devices in North America.McConway & Torley, LLC is searching for Grinder in our Pittsburgh, PA plant.
As a Grinder at McConway and Torley, you'll use grinders or chipping hammers to remove excess steel, bevel, round or straighten edges, and remove defects, burrs and holes in order to meet product specifications.
You'll also inspect the final product using production gauges.
What You'll do:
Operate band saw, abrasive saw, sand grinder, belt grinder and portable pneumatic grinding tools
Use of a variety of hand tools including hammers, cold chisels and files
May require the operation and/or loading of the blast cleaning machine
Report production quantities and items for each work order
Perform any and all other job related tasks as assigned
What you'll need:
Minimum of 1 year experience operating at least one of the following: Band Saw, Abrasive Saw, Sand Grinder, Belt Grinder, or Portable Pneumatic Grinding Tools
Experience in a foundry or manufacturing environment is preferred
Math, computer and communication skills are necessary
Must be able to understand and follow verbal and written instructions
Lift up to 25 lbs. on a frequent basis floor to shoulder
Lift up to 50 lbs. on an occasional basis floor to shoulder
Carry up to 50 lbs. on an occasional basis less than 25 feet
Push/pull up to 30 lb. molds waist to chest level to/from the grinding wheel on a frequent basis
SUMMARY OF FUNCTIONS:
To produce usable, extrusion quality material from scrap products produced during pipe manufacturing
DUTIES AND RESPONSIBILITIES:
Segregate the different types of scrap products to be reground.
Clean scrap material to prevent contamination of the ground material with foreign objects and dirt.
Use chain saws or other equipment, as needed, to cut up scrap material.
Determine weight of scrap on weigh scales and maintain a written record of the amount of scrap ground.
Operate the scrap grinding equipment and feed scrap product into the grinders.
Operate fork lifts and other lifting equipment, as needed, to handle scrap.
Maintain the organization and cleanliness of the scrap holding area.
Empties trash from work area as required..
Breaks down empty gaylords as received from Extrusion.
Follows all safety requirements of this position.
Abides by all policies and procedures in the associate handbook.
Performs all duties as directed by management.
EDUCATION AND/OR EXPERIENCE REQUIREMENTS:
High School diploma or GED from a state recognized institution is desired.
Mechanical aptitude: ability to operate power grinding equipment and power hand tools.
Ability to lift 40 pounds without reasonable assistance.
Ability to lift 70 pounds with reasonable assistance.
Mobility sufficient to allow frequent entrance and exits from lift truck.
Ability to work in high temperatures for extended periods of time.
Must be able to wear dust mask, earplugs, face shields as necessary.
Works in close proximity to power granulating equipment and high decibel noise emission for extended periods.
Works in dusty conditions. Respiration filtration is frequently worn.
Duties require the use of and operation of power hand tools and the lifting of heavy objects.
Wabash National is more than a place to work. It is a place to contribute your talents, taking pride in being part of a team that moves diverse industries forward through innovative solutions. Each associate is a valued team member, empowered to carry forward the legacy of innovation that jumpstarted the company over 25 years ago.
If you are applying for a position with certain of Wabash National Corporation's subsidiaries, such as Garsite/Progress LLC, Walker Stainless Equipment LLC, or Brenner Tank, LLC, with locations in Kansas and Wisconsin, please know that these companies are equal opportunity/affirmative action employers. You can learn more about your rights by viewing the federal "EEO is the Law" poster at http://www.dol.gov/ofccp/regs/compliance/posters/pdf/eeopost.pdf.
If you are passionate about making a difference and being part of a team that is shaping the future, take a closer look at Wabash National. We look for strong, stand-out recruits with the desire to elevate our organization and make it the best it can be – for our associates, our customers and our community.
Overview of Position:
Operates precision grinding machines to assemble products and product parts to established blueprint and engineering specifications consistent with job specifications and quality standards. Selects, mounts, attaches and calibrates a variety of attachments, grinding machines to grind angles, contours, lines, spheres, etc. on to surfaces.
Description of Duties/Responsibilities:
Prior to beginning work, inspects equipment to assure that it is in safe operating condition and that any required preventative maintenance checks have been completed.
Performs routine maintenance as required.
Reads and interprets blueprints and work orders to insure that specifications and tolerances are met.
Develops and applies knowledge of specified finishes and the proper operating sequence of grinding steps to obtain desired results.
Obtains material, parts and tools as needed to complete job.
Sets up, adjusts and operates equipment in a safe, efficient and accurate manner to produce required parts.
Grinds welds, deburrs rough metal, produces various finishes on metal.
Works to reduce scrap and improve quality.
Checks work to make sure it meets specifications and tolerances.
Accurately completes all required paperwork, including recording labor data.
May be assigned to other tasks as needed to meet work load demands.
Keep Supervisor advised of any quality problems, concerns, delays, etc.
Advise Supervisor of any maintenance work. Maintain an orderly and safe work environment.
Suggest methods improvements or alternate methods and materials to reduce cost and/or improve quality
Performs other duties as apparent or assigned.
Preferred Qualifications (Education, Experience, Skills, etc.):
Familiar with a variety of the field's concepts, practices, and procedures. Demonstrates ability to read, interpret and apply blueprints, weld symbols and procedures.
Equal opportunity employer. This company considers candidates regardless of race, color, religion, sex, sexual orientation, gender identity, national origin, disability or veteran status.
Wabash National is a tobacco free environment.
If you need any assistance seeking a job opportunity at Wabash National Corporation or any of its affiliates, or if you need reasonable accommodation with the application process, please email firstname.lastname@example.org.
Tool Grinder / Cutter - 1St Shift
Requisition ID 104244BR Date updated 12/12/2017
Manufacture and resharpen various cutting tools utilizing manual tool grinders. Understanding and supporting the needs of our internal customers and support groups will be a key factor. Work with the customers to make improvements to cutting tools
Commitment to Safety
Interpret cutting tool blue prints and specification sheets
Set up and operate manual tool grinding machines (Monoset, Dedtru, etc)
Fabricate new cutting tools to specifications
Modify and regrind existing tools to specifications
Use measuring tools including micrometers, calipers, and indicators
Inspect your own work
Monitor and maintain quality
Perform duties with minimal supervision
Knowledge of cutting tool geometries.
Able to work any shift
Written and verbal communication skills
Basic math skills
Timely problem resolution.
Effective communication skills.
Ability to adapt to changing product requirements.
Positive, proactive attitude and work approach.
Effective time management skills.
Previous Walter Power CNC grinder Programming experience utilizing Walters Tool Studio Software,
Previous Walter Power CNC grinder set up and operation
Required Education (including Major):
- High School diploma or equivalent.
Business Unit Profile
Raytheon Missile Systems (RMS) is the world leader in the design, development and production of missile systems for critical requirement including air-to-air, strike, surface Navy air defense, land combat missiles, guided projectiles, exoatmospheric kill vehicles, missile defense and directed energy weapons. RMS is headquartered in Tucson, Arizona with over 11,000 employees operating at sites across the country and internationally.
None / Not Required
Type Of Job
TX - Dallas
Raytheon is an Equal Opportunity/Affirmative Action employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, creed, sex, sexual orientation, gender identity, national origin, disability, or protected Veteran status.
Concrete Grinder Operators - R&B - Macon, GA
The Penhall Company has an immediate openings for experienced Grinder Operators to join our Highway, Runways, & Bridges Division. Must have a minimum of 5 years' experience in operating a pavement diamond grinder (to include PC 5000A, PC 5000B, PC 6000, or Penhall built G 38's a plus). Position would require extensive, overnight travel to project locations as assigned. We are currently operating in WA, CA, ID, CO, UT, TX, KY, NC, SC, FL,
Penhall has been the go-to concrete services partner for a wide-range of industries since 1957. What began as a single flat saw operation has developed into an expansive offering of concrete solutions, including concrete scanning, cutting, sawing and breaking/removal, grinding, grooving, and rumble strips. Today, Penhall is the largest U.S. supplier of concrete services. Our capabilities and expertise span across 43 locations in 21 states & Canada.
Essential Skills, Knowledge and Abilities
Must have a least 5 years minimum experience in operating a pavement diamond grinder.
Strong mechanical abilities.
Ability to communicate and interact with customers efficiently.
Excellent verbal and written communication skills.
Ability to complete all necessary daily paper work applicable to Penhall, DOT, FMCSA, and IFTA requirements.
Able to work without continuous supervision.
Able to lead and work with others.
Willingness to travel for extended periods of time. Work all shifts, work extended hours, and work in extreme conditions.
Able to lift & move 45lbs or more
Penhall Company offers:
A full time career opportunity & competitive wages,
Affordable Medical, dental, vision & life insurance, vacation, holiday & sick pay, 401K retirement play w/ company match.
Mentor Program dedicated to Safety, Training & Continuous Improvement
The Penhall Company is an Equal Opportunity Employer. Penhall Company encourages qualified females, minorities, veterans and disabled persons to apply.
Making better hires starts with building better job descriptions
- Browse 100s of templates across 40+ industries
- Customize your template with your company info & job requirements
- Post it to 20+ job boards in seconds – for FREE!